DIGITAL METER

1. [Track multi cables] Trace and locate RJ45, RJ11,USB,BNC cables;
2.[Hub blink] locating for locating network port by the flashing port light on Hub / Switch.
3. [Track with AC filter] Easily tone trace cable without AC current noise.
4.[Length and Faults location] Measure cable length for RJ45,BNC cable.
5.[Cable continuity] Check open, short, cross for RJ11,RJ45, BNC Cable

1. [Cable track] Locate cable quickly among lots of unknown cables;

2. [Cable continuity] Verify Lan cable (open,short, cross) ;

3. [Pin-to-pin] Pin to pin cable map for indiviual cable (not by pairs) ;

4. [Direct cable lead] clips are connected with transmitter directly;

5. [Certificates approved] CE/FCC approved;

NF-810
Wire Tracker
1. Tracking RJ11, RJ45, cables or other metal wire.
2. Check wiremap of Lan cable.
3. Telephone Line Test: Judging TIP or PING line and polarity test.
4. Detect Ethernet network for Power over Ethernet existence.

Underground Wire Locator
1. Helpful-locating & tracking buried and hidden wires
2. Easily locate pet fence wires, metals pipes, electrical wires, etc.
3. Wire tracer range-up to 2.6 feet deep and 1640 feet in length.
4. Power: 9V Alkaline battery (NF817)

1.[POE function] Test the information of standard / non-standard PoE device, such as voltage, polarity, midspan or endspan. 2.[Power & Current ] Test of real-time power, current, voltage consumed by PD devices in PoE power supply systems. 3.[Cable Continuity] Test the open, short, cross status in the network cable. 4.[Loopback] The loop test function of the switch.

1.Start capacity has two modes:quick test /accurate test.
2.Start system load test&Max load test.
3.Use tor all batteries 12V 24V with 100 – 2000 CCA lead-acid batteries.
4.Check the overall health ot the battery including the cranking test,
and run a complete system charging test.

1. Telephone line status detection.
2.Port flash.
3. NCV
4.Led Lighting.
5. Headphones
6.Low battery prompt and charging
7. Cable tracing
8.QC for RJ45 plug crimping quality test

1.Detecting the idle , ringing, busy status of the telephone line and the polarity test of the telephoneline.
2.Two continuity test mode: cont mode and tone mode.
3.Tracking the network cable with short-circuin for Cat3/telephone line/coaxial cablle/audio/video signal cable.
4.Testing telecom equipment and router live power Status.

Underground Wire Locator
1. Helpful-locating & tracking buried and hidden wires
2. Easily locate pet fence wires, metals pipes, electrical wires, etc.
3. Wire tracer range-up to 2.6 feet deep and 1640 feet in length.
4. Power: 9V Alkaline battery (NF817)
5. Power: Rechargeable Lithium battery (NF-817L)

1.[3 scan modes] Digital mode/ Analog mode/ PoE mode to locate cable in different situations.
2.[Cable Length measurement] Measure cable length accurately the range is 3~200m. No calibration needed 3.[Voltage detector] Detect AC voltage presence (50V-1000V).
4.[Cable Continuity] Test physical status for STP, UTP lan cable.
5.[Hub blink] Locating network port by the flashing port light on Hub / Switch. and testing transmitting mode and speed of switch.
7.[PoE testing] identify which pins are providing power and detect how much voltage, identify which the type of PSE (at/af standard)
8. RJ45 plug crimping checking, Lithium battery for transmitter and receiver

1. Power socket test
2. Power line checking for fire/earth/neutral

TDR theory to measure length of cat5e, cat6 and cat7 cable, coaxil cable, telephone cable.
2. Wiremapping with length and provide the distance to fault information.
3. PoE function: identify which pins are providing power and detect how much voltage.
4. PING function to test network performance, data packet, MIN&MAX time.
5. Quickly find the targeted cable without stripping isolation among unknown cables.
6. Hub blinks for locating network port by the flashing port light on Hub / Switch.
7. Voltage detector: included in receiver (90~1000V)

MINI Optical Power Meter 1.Optical power meter

2.HD display clear handwriting

3.Network test,applicable to FC,ST,SC,interface

4.USB lithium direct charge 5.Automatic shut-down

6.Support 850/980/1310/1490/1550/1625nm wavelength,

7.Measurement range-60 to+8dBm. 8.Cable continuity testing function .

MINI Optical Power Meter

1.Powerful red light

2.Optical power meter

3.HD display clear handwriting

4.Network test,applicable to FC,ST,SC,interface

5.USB lithium direct charge

6.Automatic shut-down

7.Support 850/980/1310/1490/1550/1625nm wavelength,

8.Measurement range-60 to+8dBm. 10.Cable continuity testing function .

MINI Optical Power Meter
1.Powerful red light

2.Optical power meter

3.HD display clear handwriting

4.Network test,applicable to FC,ST,SC,interface

5.USB lithium direct charge

.Detecting Frequency: 1MHz-8000MHz.
2.Detecting Dynamic Range >73DB
3.Detecting Sensitivity ≤0.03 mw(Main Frequency)
4.Signal Strength Indicator 9-level LED bar graphs to show 9 signals strength levels
5.Battery Embedded with 3.7V 300mA Lithium Polymer battery providing 25 continuous working hours and up to 10 days for standby.
6.Magnetic Field Detection range <10cm
7.RF Signal Detection range 10~15cm(Depend on sensitivity)

Main function
1. Directly hunt 5E, 6E, telephone wire, coaxial cable, USB cable and other cables.
2. Hub blink for locating network port by the flashing port light on Hub / Switch.
3. Check wiring error in 5E, 6E, coaxial cable, such as open ,short , cross,ect .
4. Measure cable length and determine the distance of broken point.
5. Testing polarity and voltage.
6. Memory for calibration data storage.
7. Automatically time-delay shut off and backlight display function.
8. Anti- burnt level :100V

1.[Cable continuity] Check wiring error for STP/UTP, such as open,short, cross connection; 2.[Length and Faults location] Measure length for Lan cable accurately; 3. [Calibration memory] Memory and storage function; 4. [Screen with backlight] Backlight for work in darkness. 5. [Multi remote adaptors] 8 remote units included (only for NF8108-M)

1. TDR theory for length measurement
2. POE testing: af/at/bt standards
3.Ping Scan function
4. Port Flash function
5. IP scan function
6. NCV function

1.[PoE Testing] identify which pins are providing power and detect how much voltage . 2. [PING Testing] to test network performance, data packet, min & max time. 3.[Track with AC filter] Tone trace cable with complete AC Interference Rejection 4.[Hub blink] locating network port by the flashing port light on Hub 5.[Length and Faults location] Measure length of network cable, coaxial cable, telephone cable. 6. [Cable continuity] Capable to test open, short, cross connection, 7. [Data export and print] TF function to import and export data from comupter 8. [Voltage detector] tone probe can be used to detect voltage (90-1000V) 9. [Multi remote adaptors] 8 remote identifiers are included; (only for NF-8601W)